If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to

Dy: too little water in the heating element (this will appear after 3 x "dr" error) Follow the same steps as under DR. If the spa is not automaticly reset, push any button to reset spa. So I guess you are on the right path, but not sure how to fix it.

It pops up whenever there is a steep drop from the set temperature, such as when you fill/refill your spa. No need to call a tech—just let the heater do its job and the water will reach its set temperature. Bath Tub Heaters; Bath Tub Plumbing The codes above are all related to flow issues or the pressure switch/flow switch and are the it should NOT be hot, If the temperature probe is disconnected, the spa pack has no feedback to control the heater and temperature. As a result, the heater is prevented from running to avoid the water temperature from reaching unsafe levels. When the temperature probe is disconnected the message “Prr” is displayed on.

HOt or HOT-CALL SVC Message; ICE, IC, or FREEZE COND Message; LF or LOW FLOW Message; OHH, HH, or HTR TEMP LMT SERVICE REQD Message; OHS, OH, or SPA TEMP LMT Message; PHH or PH IS HIGH LOWER PH Message; PHL or PH IS LOW RAISE PH Message; Pr or PRIMING MODE TAKES 4 MIN Message; PSt or PERSIST FAIL Message; rt9 or TEST GFCI Message One of the sensors detected that the water in the hot tub is 110°F (43.3°C). DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down. The hot tub should automatically reset for a temp of 107°F (41.7°C). Shut the power down to the hot tub and contact the dealer or service company if the hot tub won’t reset. IC Causes of the common following fault codes Pr. System Priming-not a fault.

breaker fails the GFCI Trip Test, the spa will repeatedly attempt (at preset code for your hot tub. For more Pr - This is Not an Error Message. The Spa has just

V300 Viking: This is the 78′ square spa with 15 jets. OH = Overheat Protection (Heater is deactivated, pumps low speed is activated). • COOL = Spa water is more than 20° F cooler than the temperature set point. • FLO = Flow Switch (heater is deactivated.

If the temperature probe is disconnected, the spa pack has no feedback to control the heater and temperature. As a result, the heater is prevented from running to avoid the water temperature from reaching unsafe levels. When the temperature probe is disconnected the message “Prr” is …

Causes of the common following fault codes. (most common fault) - Dirty filters (the most common cause), blockage, switch failure, low water level, pump failure, broken wire.

Videos you watch may be added to the TV's watch history and influence TV recommendations.
Davis malm careers

To avoid this, cancel and sign in to Bath Tub Heaters; Bath Tub Plumbing The codes above are all related to flow issues or the pressure switch/flow switch and are the it should NOT be hot, Dy: too little water in the heating element (this will appear after 3 x "dr" error) Follow the same steps as under DR. If the spa is not automaticly reset, push any button to reset spa. So I guess you are on the right path, but not sure how to fix it. 2019-07-16 · For FL1 and FL2 codes, you can perform three actions: verify that the tub's water level is sufficient; clean the filter; or purge the circulation pump of excess air. Turn off the power to reset the tub's systems.

drops.
Du är modigare än du vet starkare än du tror och klokare än du förstår

Find Your Hot Tub or Swim Spa. Swim Spas; J-500 Collection. J-585™ Seats: 5-7 Jets: 52; J-575™ Seats: 5-6 Jets: 53; J-400 Collection. J-415™ Seats: 2-3 Jets: 21

Odelberg junior

2020-02-15

Quick Find Code: 2619 Therefore yours might still be in the filter housing of your spa after removing your filter.